Menu
Podpora
Literatúra a softvér

Literatúra a softvér

Technická knižnica Megger vám dáva prístup k širokému zoznamu odbornej literatúry, ako sú aplikačné príručky, aplikačné články a ďaľšie. Zároveň tu nájdete na stiahnutie aktualizácie prístrojových a PC softvérov pre vybrané produkty. Použite filtre pre vyhľadanie špecifického obsahu (napr. aplikačné články) alebo spresnite vyhľadávanie výberom konkrétnej aplikačnej oblasti. 

Pre získanie pristupu ku Softvéru a k Aplikačným príručkám (en), prosím vytvorte si užívateľský účet .

Ostatná časť Technickej knižnice je dostupná bez registrácie.

Filtrovať podľ plikácie:
    Zobrazované položky 1 - 10 z 148 celkovo
Measuring cable impedance with SVERKER900
This is an easy solution to measure the impedance values for cables, the values are used for calculation of compensation factor in distance protection.The compensation factor is first theoretically calculated and these values can now be compared with the measured values.
Uverejnené: 14 decembra 2020
Stiahnuť PDF
Preventive maintenance of rolling stock
The test and maintenance of electrical components on rolling stock is not an easy job to do. Some maintainers dismount some of the parts and bring them to a central location for revision and maintenance. This is a cumbersome and time consuming exercise. In many cases, the electrical parts are replaced only when they break down and are not subject to periodical testing. This of course holds a risk as some parts, e.g. circuit breakers, are crucial for safety reasons.
Uverejnené: 3 novembra 2020
Stiahnuť PDF
Case Study on IDAX300 and VAX020
The Power Grid Corporation of India Limited (PGCIL) is an Indian state-owned company headquartered in Gurugram (North India) engaged mainly in Trans-mission  of  Power  and  transmits  about  50%  of  the  total  power  generated  in  India  on  its  transmission  network.  The  company  owns  and  operates  about  1,61,790  circuit  kms  of  transmission  lines  at  800/765 kV,  400 kV,  220 kV  &  132 kV EHVAC and +500 kV HVDC levels and 248 sub-stations. Also, it has the transformation capacity of about 396 825 MVA as of 30th November 2019.
Uverejnené: 26 augusta 2020
Stiahnuť PDF
TTRU3 Factory ratio testing of power transformer
Transformer equipment manufacturers (OEMs) have a critical need to measure true ratio, as they must confirm proper manufacture of their transformers during construction and final assembly. Improper construction has consequences of higher cost, late delivery, and poor quality. The ability of a ratio instrument to be used for all steps involved makes it a practical valueto OEMs because only one instrument is purchased and used throughout each stage. Only the most reliable and accurate instruments make it to the factory floor. Winding stack under constructionre used: Art Mandigo Winding Service.
Uverejnené: 3 augusta 2020
Stiahnuť PDF
Testing frequency relays with SVERKER900 considering the IEC 60255-181 standard
This application note is more than a description of how to use SVERKER 900 for testing frequency relays. It also wantsto spread the knowledge about IEC standardization in relay protection. Many engineers often associate theIEC series of protection standards IEC 60255-1xx1to relay type testing, and believe that they do not need to have competence about this series of standards. This is a misunderstanding: many of the concepts, definitions and test procedures described in thestandards are there to be used in relay technique, no matter if the role is relay manufacturer, user, or commissioning / maintenance testing engineer ([2], [3]).
Uverejnené: 30 júla 2020
Stiahnuť PDF
DLRO2: long test lead test mode
When measuring very low resistance the four-wire test method has for many years been the standard method. The main advantage being that it simply and easily removes the resistance of the test leads from the measurement. However, what happens when those test leads need to be verylong?
Uverejnené: 27 júla 2020
Stiahnuť PDF
DLRO2: diference meter
Introducing the first low resistance ohmmeter to feature a difference meter, a device that turns changes in resistance into a moving pointer and percentage change. When testing multiple similar connections, it makes it easy to spot those small increases in resistance that eventually turn into major faults.
Uverejnené: 27 júla 2020
Stiahnuť PDF
DLRO2 safety warnings
Safety warnings for DLRO2
Uverejnené: 14 júla 2020
Stiahnuť PDF
One touch OLTC with the TTRU3
Completing turns ratio tests on all transformer taps can be a cumbersome process. With One Touch OLTC from the TTRU3, anyone can configure and test all taps within a few short minutes.
Uverejnené: 22 apríla 2020
Stiahnuť PDF
TTRU3 Calibration verification
When performing calibration verification of the TTRU3, the following factors need to be considered to achieve accurate measurements and prevent damage to your calibration fixture or TTRU3.
Uverejnené: 20 februára 2020
Stiahnuť PDF
  • 1
  • 2
  • 3
  • 4
  • 5
  • ...
  • >
  • Zobrazované položky 1 - 10 z 148 celkovo